system state backup failed in windows 2008
I try to run system state backup in my machine which windows 2008 (enterprise) using wbadmin tool. Im getting following error
Error [0x8007045d] The request could not be performed because of an I/O device error.
and sometimes
Error [0x80070017] Data error (cyclic redundancy check).
I restarted and gave full permission ( defragmentation, chkdsk) nothing helped...
Any one tell me how to getrid of this error, is there any soluion for this ?
Thanks In advance ... Urgent....
Regards,
Prince.
ilavaa
- Changed type Christine Fok Wednesday, January 14, 2009 3:11 AM changing to discussion while waiting for customerr's reply
Reply:
We have seen such issues primarily due to a fault with the underlying hardware. To isolate the root cause, can you try running the backup to another disk so that we can be sure if the issue is coming from the backup target volume?
Thanks,
Prabu.
Prabu A [MSFT] ---- This posting is provided "AS IS" with no warranties, and confers no rights
------------------------------------
Reply:
I have checked by giving some other drive as dump location. But still im getting the errors. Previouly I had Windows Xp in that machine n I formatted and installed windows 2008.
If it is hardware failure means can you tell the good h/w configuration to run System state backup?
Regards,
Ilavaa.
ilavaa
------------------------------------
Reply:
* Was the chkdsk green on both the source volumes as well as target disk?
* Can you open the error log file reported by wbadmin.exe which has the list of files failed and check if there are any entries
present?
GeethaKrishna
------------------------------------------------------------------------------------
GeethaKrishna [MSFT] ---- This posting is provided "AS IS" with no warranties, and confers no rights
Messages posted to this forum are provided "AS IS" with no warranties
------------------------------------
Reply:
Yes. I have done both the things you said.
Error [0x8007045d] The request could not be performed because of an I/O device error. - this error comes at 0% dumps.
And the CRC error stops always when it dumps logon.scr file.
Do u have any idea?
Regards,
Ilavaa.
ilavaa
------------------------------------
Reply:
Can you please run chkdsk /r /b <Drive>:
This will fix the source disk for any bad sectors.
Then do the System state backup.
Messages posted to this forum are provided "AS IS" with no warranties
------------------------------------
Command reference link for Volume Shadow Service operations
Configuration Manager is dependent on the Volume Shadow Service -here is a link to the official VSS command reference:
http://technet.microsoft.com/en-us/library/cc754968.aspx
Here is a cheat sheet with some basic commands with their sample output.
D:\vssadmin Add ShadowStorage /For=D: /On=E: /MaxSize=30000MB Successfully added the shadow copy storage association D:\>vssadmin List ShadowStorage Shadow Copy Storage association For volume: (D:)\\?\Volume{01a9f46c-9841-11da-8376-806e6f6e6963}\ Shadow Copy Storage volume: (E:)\\?\Volume{201f6ac3-5da3-45dc-af52-15627f9a66db}\ Used Shadow Copy Storage space: 0 B Allocated Shadow Copy Storage space: 0 B Maximum Shadow Copy Storage space: 29.297 GB D:\>vssadmin Delete ShadowStorage /For=D: /On=E: Successfully deleted the shadow copy storage association(s) D:\>vssadmin Add ShadowStorage /For=D: /On=E: /MaxSize=3000MB Successfully added the shadow copy storage association D:\>vssadmin Resize ShadowStorage /For=D: /On=E: MaxSize=30000MB Successfully resized the shadow copy storage association D:\>vssadmin List Writers vssadmin 1.1 - Volume Shadow Copy Service administrative command-line tool (C) Copyright 2001 Microsoft Corp. Waiting for responses. These may be delayed if a shadow copy is being prepared. Writer name: 'SqlServerWriter' Writer Id: {a65faa63-5ea8-4ebc-9dbd-a0c4db26912a} Writer Instance Id: {74a867dd-651b-4b76-93cf-ec1864f2ab11} State: [1] Stable Last error: No error Writer name: 'SMS Writer' Writer Id: {03ba67dd-dc6d-4729-a038-251f7018463b} Writer Instance Id: {3b455ba2-b180-40b4-b295-b5fa2264ffd7} State: [1] Stable Last error: No error
Vista Ultimate to 2000 Pro
basic file sharing. I have usernames and passwords setup on all computers, same user/password on all
1 2000 pro computer
2 xp computers
1 vista computer
xp computers can access 2000 and vista shares fine
2000 pro can access xp and vista shares fine
vista has problems accessing 2000 shares, xp is fine.
When I click on the computer name in the network list of computers, It asks for User name/password. I type it in, and says Unable to Logon, check username/password etc.....I have tried guest account, etc.
Now I just accidently hit the minus sign key twice and hit enter, and it logged on and saw all the shares. " -- " is all I entered for a username, no password, and then the shared folders showed up.
I don't understand this, why it wont log on with the username's i've set up
anyone have a clue?
Reply:
Hi,
Before moving on, could you please confirm the following point?
Can you access Windows 2000 share folder with another Windows 2000 user/password from Windows Vista machine?
Then, I suggest enabling Netmon on the computers to capture the network packets.
NOTE: Please reproduce the problem two times. One time with password, one time without password. Thank you for your cooperation.
1) Download NetMon3.2 from the following website and install it on the both computers
http://www.microsoft.com/downloads/details.aspx?FamilyID=f4db40af-1e08-4a21-a26b-ec2f4dc4190d&DisplayLang=en
2) Log onto the machines, right-click the Netmon icon and select Run as Administrator to launch NetMon3.2.
3) In the Microsoft Network Monitor 3.2 window, click Create a new capture tab …
4) In the new tab, select all the Network Adapters in the Select Networks window.
5) After that, press F10 to start NetMon.
Note: Please start NetMon on both machines.
6) Try to re-produce the problem on the computer.
7) Go back to the NetMon window and press F11 to stop the NetMon.
8) Press Ctrl+S to save the Netmon file and upload them to the following space:
https://sftus.one.microsoft.com/choosetransfer.aspx?key=f7451207-0164-4f16-bce1-7a2f68fb2549
Password: cYhdka!OPY
In addition, please understand that analyze/troubleshoot this kind of issue may be time consuming. If it is urgent, I'd like to recommend that you contact Microsoft Customer Support Service for instant assistance.
To obtain the phone numbers for specific technology request please take a look at the website listed below:
http://support.microsoft.com/default.aspx?scid=fh;EN-US;PHONENUMBERS
Thank you for your cooperation.
Hope it helps.
------------------------------------
Reply:
As this thread has been quiet for a while we will be changing the issue type to 'Comment'.
If you wish to return to this question you can go ahead and change the type back to 'Question'. Then you can edit your initial post and change the radio button at the top of the post editor window.
If the issue has been resolved, we'd love to hear your solution. By sharing your experience you can help other community members facing similar problems.
Thanks!
------------------------------------
Reply:
------------------------------------
Reply:
Hi,
Please start NetMon on both machines. Thank you for your cooperation.
------------------------------------
SDS Examples Updated for Pulbic CTP Server
Mike Amundsen [http://amundsen.com/blog/]
Lexmark USB printer 3100 series
Reply:
Hi,
Thank you for your information. This post will be referred by more people.
------------------------------------
Suggestions for Paging Support in SDS Responses
Currently SDS returns a maximum of 500 entities per query regardless of the number of entities that match the query criteria. Going forward it is important to provide support for paging control. Ideally this should be done as message metadata, not as part of the query itself. One possible exception would be to use the
Take(n) query function currently supported by SDS as part of the paging control metadata. A good example of a pattern already 'vetted' by the community is the Feed Paging and Archiving standard developed for the Atom MIME-type. Since SDS seems committed to supporting Atom at some point in the future, using the above-mentioned RFC standard seems a good target. For MIME-types other than Atom, it is suggested that a set of custom HTTP Headers be employed to cover the same values. Suggested names are:
x-paging-first, x-paging-previous, x-paging-next, x-paging-last. In line with RFC5005 (see above), the values should be links, not scalar values. This allows the greatest flexibility for future changes to the way paging is used and/or computed (i.e. x-paging-next: http://example.com/container/entity-25) Another possible solution would be to consider the HTTP Header Linking draft from Mark Nottingham (i.e.
link:<http://example.com/container/>; rel="first"). While this draft is currently dormant, it has potential for wider acceptance over adopting custom HTTP headers. Looking forward to feedback.
Mike Amundsen [http://amundsen.com/blog/]
Disk Corruption Increase
Just a general question (at least to start with!) Since I've been using Windows 2008 I've seemed to experience a lot more disk corruption. This is across two computers with completely different architectures (775 versus 771) and different power supplies (although to be fair they are fed from the same power feed ultimately.) I have recently just rebuillt my VM host because one of the mirror drives failed and in trying to recover the mirror failed completely. All VM's suffered internal disk corruption messages.
Has anyone else experienced this behaviour or is it time to invest in a surge protector etc?!? Any other ideas of how disk corruption could "suddenly" become so common other than the wife taking it out on my computers when I am not there :)
Cheers
D
Publish ProClarity book (*.bbk) with all pages through .Net (C#)
// Created by : Bimal Parekh
// Description: This class will help to publish the Proclarity report to the PAS
//you just have to add the following refrences before you begin
//Web Reference : "ProClarity" -> http://<ServerName>/PAS/pstore?WSDL
//Refrence (COM references) : Interop.PBB.dll, Interop.PCDS5.dll, Interop.PESIntegration5.dll, Interop.PLOGSERVER.dll, Interop.PTMD.dll
using System;
using System.Collections.Generic;
using System.Text;
using PESIntegration5;
using System.Xml;
using System.IO;
using System.Net;
namespace CustomInstall
{
class ProclarityInstaller
{
private string _ProclarityDomain;
private string _ProclarityUser;
private string _ProclarityPwd;
private string _ProclarityDeploySite;
private string _ProclarityLibrary;
public String BookPath;
Uri serviceUri;
ProClarity.PStore myObj ;
public ProclarityInstaller(String _DeploySite,String _Domain,String _User, String _Password,String _bookPath,String _libraryName)
{
_ProclarityDomain = _Domain;
_ProclarityUser = _User;
_ProclarityPwd = _Password;
_ProclarityDeploySite = _DeploySite;
_ProclarityLibrary = _libraryName;
BookPath = _bookPath;
serviceUri = new Uri(_ProclarityDeploySite + "/PStore.asp");
myObj = new ProClarity.PStore(serviceUri.AbsoluteUri);
ICredentials _credentials;
NetworkCredential credentials = new NetworkCredential(_ProclarityUser, _ProclarityPwd, _ProclarityDomain);
_credentials = credentials;
myObj.Credentials = _credentials;
FileInfo[] _reportFiles = null;
_reportFiles = getProclarityBooksList(BookPath );
foreach (FileInfo _report in _reportFiles)
{
String _reportname = _report.FullName.ToString();
PBB.BriefingBookClass _Pbook = new PBB.BriefingBookClass();
_Pbook.Open(_reportname, false);
String _bookName;
_bookName= _report.Name.Replace(".bbk", "");
PESIntegration5.PClient2 _publishBook = new PESIntegration5.PClient2();
_publishBook.Login(_ProclarityDeploySite, _ProclarityDomain + "\\" + _ProclarityUser, _ProclarityPwd);
_publishBook.EnablePublishing = true;
if (getBookId(_ProclarityLibrary, _bookName).ToString() != "")
{
exists");
//deleteBook(getBookId(_ProclarityLibrary, _bookName));
}
else
{
//Publish Proclarity Books
_publishBook.PublishBriefingBook(false, _Pbook, _bookName, "", "", getLibrariyID(_ProclarityLibrary));
// Update the connection information
String result;
result = _publishBook.UpdateConnectionInfo(getBookId(_ProclarityLibrary, _bookName), PCDS5.UpdateConnInfoType.uciBook, "", "", "", "", "", "", "", "", "{176941F9-18E8-47D6-860D-006FF2655608}", "MSOLAP (SQL 2005)", "ServerName", "ServerName", "Database", "[cubename]", "CubeName", "\\", true);
//{A07CCD0C-8148-11D0-87BB-00C04FC33942} ->MSOLAP (SQL 2000)
//"{176941F9-18E8-47D6-860D-006FF2655608}","MSOLAP (SQL 2005)"
}
_publishBook = null;
}
}
string getLibrariyID(String LibraryName)
{
XmlElement results = myObj.GetLibraries();
String LIBRARY_NAME;
LIBRARY_NAME = LibraryName;
XmlNode match = results.SelectSingleNode("//Library[@Caption='" + LIBRARY_NAME + "']");
if (match != null)
{
string libraryId;
libraryId = match.Attributes["ID"].Value;
return libraryId;
}
else
return "";
}
string getBookId(String LibraryName,String BookName)
{
string LibrartyId;
LibrartyId = getLibrariyID(LibraryName);
XmlElement results = myObj.GetBooks(LibrartyId, "Briefing Book");
XmlNode match = results.SelectSingleNode("//Book[@Caption='" + BookName + "']");
if (match != null)
{
string BookId;
BookId = match.Attributes["ID"].Value;
return BookId;
}
else
return "";
}
bool deleteBook(String BookId)
{
String result;
result = myObj.DeleteBook(BookId);
if (result != "")
return true;
else
return false;
}
private FileInfo[] getProclarityBooksList(string bbkPath)
{
DirectoryInfo _dir = new DirectoryInfo(bbkPath);
return _dir.GetFiles("*.bbk");
}
}
}
Reply:
Hi Bimal.
Did you have an actual question here, or were you just posting your code to benefit the community? Just making sure in case you had an actual question.
TJ Nelson
------------------------------------
Reply:
I have posted this article to benefit the community so other can refer and enhance this code in .net for there use
--Bimal Parekh
------------------------------------
Reply:
Hi Bimal,
When I try to publish the book from local file system, using PAS web service, the book gets published but with no pages.
Can you please help me out, in how to publish the entire book without using client assemblies (PCDS5,PBB).
Thanks
Zaffer
------------------------------------
Reply:
Hi Zaffer, did you find an answer to this problem. I am also facing the same scenario. Any help greatly appreciated.
I am using the following web method to publish a briefingbook
Function PublishBook(BriefingPak As Record, BookCaption As String, BookDescription As String, LibraryID As String, EditID As String) As String
I passed the briefing book as a single XML. The book is published but not the pages.
Thank You
Anil
------------------------------------
Reply:
Hi Anil,
Sorry but I didnt find any solution for the above problem. I had to change my design and use ProClarity Server API's instead to publish the reports.
Thanks
Zaffer
------------------------------------
Reply:
Hi Zaffer
Thank you for responding to me.
I used the proclarity desktop professional to save the book as .bbk and also as .xml. Do you know if there is an option to tell the desktop professional to generate a single XML instead of the four XML's it create when save as .XML.
For .bbk, I used BriefingBook.Open to load a briefing book object.
For .xml, I used the BriefingBook.ImportXML to load the briefing book object.
Then I tried PClient2.PublishBriefingBook to publish the .bbk ( after calling PClient2.Login and setting PClient2.EnablePublishing = true). The book is created with NO Pages.
Can you please tell me the exact steps you followed. My task is to export book to a different server.
Thanks
Anil
------------------------------------
Reply:
Where to find these DLLs? I have installed Microsoft ProClarity Software Developers Kit 6.3, do not see them..
//Refrence (COM references) : Interop.PBB.dll, Interop.PCDS5.dll, Interop.PESIntegration5.dll, Interop.PLOGSERVER.dll, Interop.PTMD.dll
Thank you
------------------------------------
Reply:
Found the DLLs in the Common Files, added references, yet the class does not compile:
The type or namespace name 'PESIntegrationUI5' does not exist in the namespace 'ProClarity.Interop' (are you missing an assembly reference?)
The type or namespace name 'PStore' does not exist in the namespace 'ProClarity' (are you missing an assembly reference?)
------------------------------------
Preventing SQL Injection Attacks The Right Way
Thought this post of mine might be of some interest to readers of this forum:
Preventing SQL Injection Attacks The Right Way
Cheers,
Mike
Reply:
For all the .NET coders out there another great tip is to stick to stored procedures, and to call them appropriately with the SQLCommand object, setting the parameters and values appropriately after specifying the command type with:
SQLCommand.CommandType = StoredProcedure
When you do this you ensure that .NET will appropriately escape the strings you send to your stored procedures which GREATLY reduces the chance of SQL injection. Of course, running the account(s) that connect to SQL with least permissions is always the way to go as well.
More info here: http://msdn.microsoft.com/en-us/library/system.data.sqlclient.sqlcommand_members.aspx
Cheers!
------------------------------------
Anyone got a sucessfull enrollment with Samsung I200
I dont have the logs here ill post anything meaningfull in them but wanted to know if anyone got it working on that device.
HTCS740 on the same setup and same sim card works like a charm.
best regards
Flemming Riis
Reply:
My initial though was that the Samsung might have provisioned different APN settings for GPRS if you are using the pre-loaded operator configurators. But if the VPN tunnel is established that shouldn't be an issue either...
Maybe something went wrong with the enrollment process? Have you tried hard resetting the device and re-enrolling it?
Have you tried the MDM Client Tools, enabled logging, and see if there's anything useful there?
Can't think of anything else at the moment. Might help if the logs give any more hints as to what the cause could be.
------------------------------------
Reply:
i forgot the device at work so cant get any meaningfull info exept that it dont work until tomorrow.
the grps network is configured and is working i tried the the same sim as in the S740 to rule out any carrier issues.
Tried 2 different i200 from factory default and ground up.
but ill post some more info tomorrow when i can get the connect log's
Would it be a idea to make a white list of devices known testet as a sticky ?
------------------------------------
Reply:
the grps network is configured and is working i tried the the same sim as in the S740 to rule out any carrier issues.
...
Would it be a idea to make a white list of devices known testet as a sticky ?
It's probably not a GPRS issue, but even though your using the same SIM card, and the same operator there is no guarantee that the settings HTC provision are the same settings Samsung are provisioning. (The configurator on the Samsung has been pretty bad before, and even configured some operators incorrectly, but hopefully they've got it sorted by now.)
The "known good devices" list was something I actually thought of a few days ago. But I never got around to doing anything about it though ;) We would need to establish a "baseline" of the tests that must be passed for it to be fully functioning.
------------------------------------
Reply:
I have been using the Samsung i200, the VPN and Policies work well. What firmware are you using?
I've already tried and failed to build a white list of working device with Microsoft Internally. There are two many variables involved. Each device, and each firmware, from different MO's will need to be tested. I had differing results testing devices against my MDM server as against Redmond MDM servers, with different SIMS. Then you have to test, VPN, Standard Policies, Software Distribution, Proxy, EXCH, OCS etc...
As I always say "If I've not tested it, I don't trust it." If you start one up, I'll be more than happy to contribute.
Cheers Wayne
Airloom
------------------------------------
Reply:
Couldnt find a update on samsung's site for it.
data
008-11-13 18:25:24 omadmclient.exe: ./Vendor/MSFT/NetworkPolicy/Bluetooth/AllowedProfiles</LocURI></Source><Meta><Format xmlns="syncml:metinf">node</Format><Type xmlns="syncml:metinf">
2008-11-13 18:25:24 omadmclient.exe: </Type></Meta><Data></Data></Item></Results><Final/></SyncBody></SyncML>
2008-11-13 18:25:25 omadmclient.exe: Successful XML->WBXML conversion.
2008-11-13 18:25:25 omadmclient.exe: WBXML for server =
2008-11-13 18:25:25 omadmclient.exe: 02 A4 01 6A 00 6D 6C 71 03 31 2E 32 00 01 72 03 ...j.mlq .1.2..r.
2008-11-13 18:25:25 omadmclient.exe: 44 4D 2F 31 2E 32 00 01 65 03 31 36 00 01 5B 03 DM/1.2.. e.16..[.
data
2008-11-13 18:29:08 omadmclient.exe: 01 01 ..
2008-11-13 18:29:08 omadmclient.exe: [PID = 0x0a840416] - Generating client's package XML
2008-11-13 18:29:08 omadmclient.exe: [PID = 0x0a840416] + Sending package
2008-11-13 18:29:08 omadmclient.exe: [PID = 0x0a840416] + Transmitting package data
2008-11-13 18:29:08 omadmclient.exe: Additional headers sent to server = "Content-Type: application/vnd.syncml.dm+wbxml
Accept-Charset: UTF-8".
2008-11-13 18:29:17 omadmclient.exe: Successfully sent data to server.
2008-11-13 18:29:17 omadmclient.exe: Server returned success HTTP status code (200).
2008-11-13 18:29:17 omadmclient.exe: [PID = 0x0a840416] - Transmitting package data
2008-11-13 18:29:17 omadmclient.exe: Package successfully sent.
2008-11-13 18:29:17 omadmclient.exe: [PID = 0x0a840416] - Sending package
2008-11-13 18:29:17 omadmclient.exe: [PID = 0x0a840416] + Retrieving server data
2008-11-13 18:29:17 omadmclient.exe: Server package's Content-Type header = "text/html"
2008-11-13 18:29:17 omadmclient.exe: Server returned unexpected Content-Type header (text/html)
2008-11-13 18:29:17 omadmclient.exe: [PID = 0x0a840416] - Retrieving server data FAILED (hr = 0x80070057)
2008-11-13 18:29:17 omadmclient.exe: [PID = 0x0a840416] + Notifying all listeners of client state
2008-11-13 18:29:17 omadmclient.exe: [PID = 0x0a840416] - Notifying all listeners of client state
2008-11-13 18:29:17 omadmclient.exe: [PID = 0x0a840416] - Running session FAILED (hr = 0x80070057)
2008-11-13 18:29:17 omadmclient.exe: [PID = 0x0a840416] - New trigger notification processing FAILED (hr = 0x80070057)
2008-11-13 18:29:18 omadmclient.exe: [PID = 0x0a840416] - OMA-DM Client Execution FAILED (hr = 0x80070057)
2008-11-13 18:29:24 omadmclient.exe: [PID = 0x69e24d9e] + OMA-DM Client Execution
2008-11-13 18:29:24 omadmclient.exe: OMA-DM Client thread priority set to 252.
2008-11-13 18:29:24 omadmclient.exe: [PID = 0x69e24d9e] + New trigger notification processing
2008-11-13 18:29:24 omadmclient.exe: Trigger notification headers = Content-Type: application/vnd.syncml.notification
X-Wap-Application-Id: x-wap-application:syncml.dm
2008-11-13 18:29:24 omadmclient.exe: Trigger notification body =
2008-11-13 18:29:24 omadmclient.exe: 6B C3 01 B0 F0 0E E9 6E 7A 6A A3 5E 55 97 F4 7A k......n zj.^U..z
2008-11-13 18:29:24 omadmclient.exe: 02 D0 00 00 00 00 17 0C 4D 53 20 44 4D 20 53 65 ........ MS DM Se
2008-11-13 18:29:24 omadmclient.exe: 72 76 65 72 rver
2008-11-13 18:29:24 omadmclient.exe: [PID = 0x69e24d9e] + Trigger notification parsing
2008-11-13 18:29:25 omadmclient.exe: Trigger info: version=11; ui-mode=1; initiator=0; session id=23; server id=MS DM Server
2008-11-13 18:29:25 omadmclient.exe: [PID = 0x69e24d9e] - Trigger notification parsing
2008-11-13 18:29:25 omadmclient.exe: [PID = 0x69e24d9e] + Running session
2008-11-13 18:29:25 omadmclient.exe: [PID = 0x69e24d9e] + Loading all initiation IDs
2008-11-13 18:29:25 omadmclient.exe: [PID = 0x69e24d9e] - Loading all initiation IDs
2008-11-13 18:29:25 omadmclient.exe: [PID = 0x69e24d9e] + Notifying all listeners of client state
2008-11-13 18:29:25 omadmclient.exe: [PID = 0x69e24d9e] - Notifying all listeners of client state
2008-11-13 18:29:25 omadmclient.exe: [PID = 0x69e24d9e] + Validating server account data
2008-11-13 18:29:25 omadmclient.exe: [PID = 0x69e24d9e] - Validating server account data
2008-11-13 18:29:25 omadmclient.exe: Client is now set to use protocol version 1.2
2008-11-13 18:29:25 omadmclient.exe: [PID = 0x69e24d9e] + Getting DevInfo data
2008-11-13 18:29:26 omadmclient.exe: [PID = 0x69e24d9e] - Getting DevInfo data
2008-11-13 18:29:26 omadmclient.exe: [PID = 0x69e24d9e] + Canonicalizing connection URL
2008-11-13 18:29:27 omadmclient.exe: [PID = 0x69e24d9e] - Canonicalizing connection URL
2008-11-13 18:29:27 omadmclient.exe: [PID = 0x69e24d9e] + Creating package #1
2008-11-13 18:29:27 omadmclient.exe: [PID = 0x69e24d9e] + Generating client Alerts XML
2008-11-13 18:29:27 omadmclient.exe: [PID = 0x69e24d9e] - Generating client Alerts XML
2008-11-13 18:29:27 omadmclient.exe: [PID = 0x69e24d9e] + Generating client Alerts XML
2008-11-13 18:29:27 omadmclient.exe: [PID = 0x69e24d9e] - Generating client Alerts XML
2008-11-13 18:29:27 omadmclient.exe: [PID = 0x69e24d9e] + Setting up client package's parts
2008-11-13 18:29:27 omadmclient.exe: [PID = 0x69e24d9e] - Setting up client package's parts
2008-11-13 18:29:27 omadmclient.exe: [PID = 0x69e24d9e] - Creating package #1
2008-11-13 18:29:27 omadmclient.exe: + Initializing SyncML processing unit
2008-11-13 18:29:27 omadmclient.exe: - Initializing SyncML processing unit
2008-11-13 18:29:27 omadmclient.exe: [PID = 0x69e24d9e] + Generating client's package XML
2008-11-13 18:29:27 omadmclient.exe: XML for server =
------------------------------------
Reply:
Our Samsung I200 seems to have gone "Walkabout" so I'll have to find it first. There may not be an update on the Samsung site, but there will be different "Flavours" of the firmware depending on which carrier cooked the rom. They have a habit of adding and removing items, which can cause inconsistencies.
Cheers Wayne
Airloom
------------------------------------
Reply:
thanks for the inputs so far ill post when i know a bit more.
------------------------------------
Reply:
------------------------------------
Reply:
Cleaned the device and tried again.
enrollservicelog
http://cid-2318cac4acc588cb.skydrive.live.com/self.aspx/Offentlig/enrollservice.txt
enrollment log
http://cid-2318cac4acc588cb.skydrive.live.com/self.aspx/Offentlig/samsung.txt
following log
http://cid-2318cac4acc588cb.skydrive.live.com/self.aspx/Offentlig/deviceupdate.log
/Flemming
------------------------------------
Reply:
I know it's the lazy man's solution, but I must admit I'm starting to think it's a bug in your version of the Samsung. (Don't know if you are using a generic Samsung ROM, or an operator-branded version.) I'll have to let the problem simmer in the back of my mind till after the weekend before I decide to give up though :)
As an experiment - is it possible to enroll the device without the VPN connection and try to do a connection direct to the DM server?
------------------------------------
Reply:
i get some of the policies pushed down it gets certs and password policy.
its not a branded samsung rom , i got a talk friday with the importer so they would look monday after a newer rom.
not possible in the test setup its located on VM's with no access other than rdp , we are moving the install monday to production so ill be able to test tuesday with the samsung directly.
thanks for taking the time to look at this.
------------------------------------
Reply:
ill post a update when i got one.
------------------------------------
Reply:
I know it's the lazy man's solution, but I must admit I'm starting to think it's a bug in your version of the Samsung.
Flemming Riis said:
We found a techie at Samsung that says its a known issue and there is a oem rom update for it that he would help find for us.
Great! The lazy man's solution was the correct solution :)
------------------------------------
Reply:
trying with pss on their enviroment to see if they can replicate the problem
------------------------------------
Reply:
Cheers Wayne
Airloom
------------------------------------
Microsoft ProClarity 6.3 SP2 (build 2217) Documenation now available
Hello all!
Microsoft ProClarity 6.3 SP2 release documents are now available at the Microsoft ProClarity team blog site. http://blogs.technet.com/proclarity/.
Enjoy!
-Joey
SSDS toolkit now available for SSRS:
http://www.microsoft.com/azure/reporting.mspx
Reply:
I'm glad you found the SSDS toolkit for SSRS. We actually had a demonstration of this at the Professional Developers Conference and now that SSDS is opened up to a Public CTP it's something we can and should evangalize more. Feel free to post your questions about the SSDS connector here in the SSRS forums and let us know what you think.
-Sean
------------------------------------
Exchange 2007, the solution for (Event ID: 1037)
Recently event viewer of our Exchange Server 2007 (non-SP1) shows below warning (Event Id: 1037):
| Event Type: Warning Event Source: MSExchangeTransport Event Category: SmtpReceive Event ID: 1037 Date: 11/23/2008 Time: 1:13:36 PM User: N/A Computer: EMAIL Description: Inbound direct trust certificate with thumbprint 594C381C4F6C9C1DC14E53F8F9A3C1966B9C63D4 has expired. Run New-ExchangeCertificate to generate a new direct trust certificate.
For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. |
Troubleshooting
We are going to delete expired certificate. So,
A. We did the following steps:
1. Runà mmc, and add "Certificates"
2. From Personal/Certificates, we explore all certificates.
3. And then we deleted the expired certificates.
B. And then we did the following steps to make sure the expired certificate is deleted:
1. On Exchange Management Shell
2. We run command: 'get-ExchangeCertificate' to make sure the expired certificate – (first one, local certificate) - is deleted.
Moreover, through the "Exchange Management Shell" we created new certificate via 'get- New-ExchangeCertificate' command.
C. We go back to step two in (A.) and found the new Certificate has been created and stored on Personal Folder of Local Computer Certificates.
D. Then we check out the Exchange Server Event Viewer, and we found same error (Event ID: 1037).
Solution:
1 We go back to step two in (A.) and then we copy the new certificate to 'Certificates' sub-folder which resides under 'Trusted Root Certification Authorities' folder.
2 And then we verified...'Event ID: 1037' is not appeared
Yaseen Alhashim
- Changed type Mike Crowley Thursday, April 26, 2012 9:35 PM
Reply:
------------------------------------
Can we run sharepoint 2003 project on Moss 2007
MCTS exams for VS 2008
Hi Friends,
I am new to this group.
I am working as a .Net developer - Web Based and SQL as backend.
I want to know how many exams are necessary for MCTS 2008. That will cover web based development as well as Database.
According to my knowledge these exams are sufficient to become MCTS 2008 on ASP.Net and Sql Server:-
1. MCTS: .NET Framework 3.5, ADO.NET Applications (Exam 70-561 SQL Server 2008)
2. MCTS: .NET Framework 3.5, ASP.NET Applications (Exam 70-562 )
3. MCTS: TS: Microsoft .NET Framework - Application Development Foundation on 2.0 (Exam 70-536)
Is there anything else I require and if any body has good study material with dumps,please let me know.
Thanks in Adavance.
Regards
Ajay Gautam
- Moved by nobugz Saturday, November 8, 2008 9:59 AM Lesson #1: learn to post correctly [loc] (Moved from .NET Base Class Library to Training and Certification)
Reply:
Yes, you are correct, the exams you have listed are MCTS: Asp.net 3.5 certifications.
Here is the link: http://www.microsoft.com/learning/mcp/mcts/vstudio/2008/default.mspx
You might want to look at SQL server 2008 certification path also.
http://www.microsoft.com/learning/mcp/mcts/sql/2008/default.mspx
There are some really good books on bookstore now with Wrox press asp.net 3.5, Microsoft press book "Programming asp.net 3.5" to help you study for the exams. Or go to msdn.microsoft.com to browse through these topics.
good luck!
------------------------------------
Reply:
What you have there is actually 2 MCTS certs, 1 is the MCTS ASP.NET and the other is the MCTS ADO.NET as both require the exam 70-536.
You dont have the requirements for an MCTS on SQL 2008.
Currently there are 3 different types, based on BI, Database Admin and Database Dev
As you are a developer, I am guessing that you will be doing the MCTS SQL 2008 Database Developer which is a single exam number 70-433
If you take a look at the exam guide for each exam you will get a good idea of what is required.
MCP,MCAD,MCSD.NET,MCTS,MCPD,MCITP Blog: http://certsandprogs.blogspot.com
------------------------------------
Soap Service Reference in VS2008 leaves much to be desired.
Generating a soap service reference currently sucks, it's a PITA to generate the proxy code and settings from the WDSL only to then have to go and manually edit the generated .cs file to alter the return types from Entity[] to List<Entity> and the app config file buffer limits, I know that its documented and not difficult to fix, but this is a "first impression" thing, really I need to be able to just generate and go.
Cheers Tim.
PS
I don't wish to come across as a prat who is never satisfied with anything, I believe in what you guys are trying to achieve and wholly support it. Just wanting you to get real world feedback.
(Anil, Ryan I met you at Mountain View for the tech partner preview sessions early this year, I was the guy who came all the way from Australia, I have huge respect for you both.)
Reply:
Thank you for your candor. Your feedback is appreciated. I have forwarded your comments to the team.
Once again Thank you.
Regards
Anil
------------------------------------
Reply:
Couple of points. First, you're quite right that you have to manually modify the buffer settings to use for large messages. Unfortunately, that is not something that's under our direct control :-( Not the greatest of things but it's what we have at this stage.
Regarding the generated .cs files. You *do* have the option of changing these. You simply need to click on the, "Advanced" button when adding the service reference. This will present you with a dialog which will allow you to choose how collections are generated for you in the proxy classes. If you wanted to do what you've done with your modifications simply change the default collection type from System.Array -> System.Collections.Generic.List and that should do the trick.
Hope this helps,
--Jeff--
JeffC
------------------------------------
Reply:
------------------------------------
red spot
i have recently had to do a complete destructive restore thanks to HP, and now the media center icon is a red spot with a exclamation point inside. and i do not know what to do. help
Reply:
i am sorry bad post. after thinking about somethiing i went in found the icons and changed it.
------------------------------------
Microsoft Certification Certificate
It has been 10 years since my last Microsoft certification, well, until last week. I downloaded an electronic copy of my certificate, and noticed that it was signed by Bill Gates, who is that guy? Just kidding. But a big deal was made recently about Mr. Gates' departure from Microsoft. I guess he is still the chairman, but is he still the 'chief software architect' like the certificate says? Not that it matters, I just was a little surprised to see it.
Joseph Durnal
http://cryptojoe.blogspot.com
Reply:
MCP,MCAD,MCSD.NET,MCTS,MCPD,MCITP Blog: http://certsandprogs.blogspot.com
------------------------------------
BURNING AVI FILES
MY LAPTON HAS STOPPED BURNING AVI FILES FOR MY DIVX PLAYER BUT BURNS NORMAL AUDIO FILES NO PROBLEM ANYONE HELP ME PLZ
Pimpin' Microsoft Press
Hope this helps!
Michael D. Alligood,
MCITP, MCTS, MCSA, MCDST, MCP, A+, Network+
The I.T. Classroom Blog
Start. Research. Plan. Perform. End. Test. Evaluate.
No comments:
Post a Comment